OT, OTN and OTS fuses are not rejection fuses -care should be taken to ensure that replacement fuses do not have lower interrupting ratings than
original fuses.
OTN 15 through 60 satisfy the Canadian electrical code requirement for Type «P» low melting-point, non-time delay fuses.
ver
Fusible TRM - Midget - Time-Delay
Tri-Onic TRM time-delay midget fuses are rated 250VAC and are offered in 36 ampere ratings from 1/10A to 30A. They have 12 seconds time-delay at 200% rating to provide supplemental protection of small motors, small transformers and other high inrush loads, plus many other 250 volt applications. (Not for Branch Circuit Protection)
ver
Fusible A70QS Amp-Trap Form 101
A70QS Amp-trap Semiconductor Protection fuses were developed in response to the need for improved overall performance of 700 volt semiconductor fuses for new equipment requirements. A70QS fuses have lower I²t for better protection, longer life when subjected to cyclic loading, plus lower watts loss. A70QS is the best choice to protect dynamic solid state equipment such as motor drives, UPS, etc.
ver
Fusible ATMR - Class CC - Fast-Acting
Amp-Trap ATMR fast-acting fuses are the smallest dimension 600V fuses suitable for branch-circuit protection. The ATMR is a popular choice for economical protection of control circuits and control circuit transformers where available short circuit currents exceed 10,000 amperes. ATMR’s rejection dimensions prevent substitution by lesser rated fuses. These fast-acting fuses give current-limiting protection to general circuits.
ver
Fusible Capacitor Protection Amp- Trap and 9F60 Series
• High interrupting capacity
• Current limitation
• Blown-fuse indication
• Direct mount
• Clip style mount
• Bus mount
• Non-venting for silent operation
• Capacitor Protection
• Power Factor Correction
Equipment
• Harmonic Filtering Equipment
• Induction Heating System
• High Power Drive
• Welders
ver
Fusible Amp-Trap® A50QS Semiconductor protection
A50QS Amp-trap Form 101 fuses grew out of the need to improve the overall performance of semiconductor fuses in response to new equipment requirements. The A50QS encompasses the best protection features lower I2t to provide better protection for equipment, longer life when subjected to cyclic loading and lower watts loss. A50QS is today’s best choice for the protection of dynamic solid state equipment such as motor drives, inverters, UPS, etc.
ver
Fusible A70QS French Cylindrical
These Premium Amp-trap French Cylindrical Semiconductor Fuses are an extension of the popular A70QS product line. They are solid-fill 14mm and 22mm fuses IEC rated 690VAC, 200kA Interrupting and 700VDC, 100kA interrupting at 10ms time constant. In addition, these fuses have an 890 VDC rating for capacitor discharge applications up to 2.5ms time constant. All ampere ratings are available with a striker. Applications include small inverter drives and UPS systems, with superior I²t for improved protection and performance.
ver
Fusible HSJ - Class J - High-Speed
The High Speed Class J (HSJ) combines the low I2t of a semiconductor fuse and the branch-circuit performance of a Class J UL Listed fuse into a single design. The HSJ can provide both branch circuit protection per NEC requirements, as well as very low I2t for protection of power semiconductors such as Diodes, SCRs, GTOs and SSRs.
Fusible ATQR Time-delay/ Class CC
ATQR small-dimension fuses feature time-delay characteristics ideally suited for the high inrush currents of control transformers, solenoids, and similar inductive loads. Mersen’s Amp-Trap 2000 ATQR fuses provide superior protection for the branch circuits of electrical distribution systems.
Fusible 1250/1300 Volt PSC Square Body
• Choice of mounting styles gives wide choice for equipment design
• Broad range of ampere ratings in a given body size for design flexibility
• UL/CSA/IEC 60269-4 compliance for worldwide semiconductor
applications
Fusible Class C Canadian Fuses
Ferraz Shawmut Class C fuses have British standard
(BS88) dimensions and are exact replacements for
the British fuses and older HRCII-C fuses. Class C fuses are not dimensionally or electrically interchangeable with other North American fuses.
They feature ceramic bodies and bolt-in mounting.
They are for short-circuit protection only, in motor controllers, for example, where overload protection is provided by an overload relay.
ver
Spanish
English
jfzgtoojov –
Muchas gracias. ?Como puedo iniciar sesion?